Through steps and photos show you how to make simple wooden model homes that will well protect it from extreme weather conditions, but also to enable him to a quiet corner in the yard, house or apartment. By the same token, you can make and homes of different shapes, colors, patterns, and so is entirely according to your taste.
There are a few tips that you should pay attention. First, it is necessary to drill a hole in a tree insert the screws to avoid splitting the wood. Also, align all components at both ends before inserting screws. Do not forget to align the walls of the vial and to allow the roof to be perfectly horizontal. Measure several times wooden parts, otherwise it may be possible that can not be adequately fit.
All necessary parts are indicated in capital letters, so if you follow these instructions and take the weekend off will succeed to create a home for a new pet that will be very grateful.
Materials Required:
A - 2 pieces of lumber measuring 2x4x92 cm (thickness x width x length), 4 pieces of 2x4x84 cm - FLOORS
B - 14 pieces measuring 2x2x61 cm long - HOLDERS OF WALLS
B - 4 pieces measuring 2x2x92 cm, 4 pcs 2x2x84 cm - Wall Plates
C - 4 pieces measuring 3,8x40x61 cm, 1 piece 3,8x36,2x61 cm, 4 cm pieces 3,8x39,4x56 - INSULATION
D - 2 pieces of plywood measuring 0,65x68,5x84 cm, 2 cm pieces 0,65x68,6xx82,5 - INTERIOR WALLS
E - 2 pieces measuring 1,58x94,6x127 cm, 2 cm pieces 1,58x79,38x91,44 - EXTERIOR WALLS
F - 10 pieces measuring 2x2x66,7 cm, cut at 45 degrees at both ends - to the roof structure
G - 1 piece of lumber dimensions 1,9x76,2x102,2 cm, 1 piece of plywood measuring 1,9x74,29x102,2 cm - SHEETS
H - 4.65 m2 tiles, slate or granules of slate and related minerals
I - 6.1 m decorative beams from 1x2 cm or 2x2 cm
TOOLS
Hammer, measuring tape, square frame
Circular saw (circular), electric drill, screwdriver
Sandpaper, protective gloves and safety goggles
The time it takes - one weekend.
The first tip is to make a frame for a house for a dog of 2x2 beams. Integrate 3.8 cm thick insulation of solid foam (polyurethane foam) within the frame dog house. Connect 1.58 cm, and connect the parts of the outer part of the frame.
Step 1
First you need to build a foundation for a house. Made the construction of 2x4 beams and attach them with screws 7.5 cm. First of all, it should be good to weigh and aligned beams to be equal. Pre-drill the construction basics, to avoid that the wood splits. Also, using a carpenter's square, adjust the beams so that they are at right angles.
Step 2
The next step is the creation of the floors, of 1.9 cm plywood which should be attached to the structure. Before you start attaching 5 cm long nails, you must make sure that the roof structure in line with the base. Use a circular saw with a fine blade to do the job quickly. Create lines and saw blade drag on it.
Step 3
Make a frame for walls of 2x2 beams. Secure the wall bracket by attaching them to the board at the top and bottom, making sure that the corners are well set. Put 7,6 cm wood screws, having a test. Pre-drill the plate before inserting 7.6 cm long nails on the floor. Align the spirit level.
Step 4
The construction of the front and rear is simple, you should follow the same procedure as above. Measure the distance between the side walls of the houses, before cut wooden parts. As you can notice in the plan, you must leave enough room for the door to open. Double foam on the walls to enable the support of an external frame around the opening.
Step 5
Build the outer walls of 1.6 cm or 1.9 cm lateral plywood. To make precise cuts, we recommend that you draw a line and use a circular saw with a fine blade. Attach the pieces to the frame with a 3.2 cm-long nail. Cut the door opening precision drill, after you make a big hole wide drill. Make the proper opening and secure it by him a good process before the board into place.
step 6
To protect your pet from extreme temperatures, it is recommended that 3.81 cm solid polyurethane foam set between two wooden pillars. So cut out the appropriate size of the board handsaw. After that, put them in the cavity between the studs. If you want to install a stronger insulation should consider making a frame of beams measuring 2x4 cm.
Step 7
On the right is a set of internal walls, made of 0.6 cm thick plywood. First of all, you need to set the side panels after measure their size. Place the plywood board in place and secure the 3.2 cm long frame. Then, install the rear and front part of the internal walls, all as previously stated. Make sure the panels are in good condition and that the nails are installed correctly, otherwise the pet may get hurt.
Step 8
Creating structures of 2x2 beams - make sure you have their ends cut at an angle of 45 degrees. All parts Treebu be the same shape and size otherwise the roof will have a symmetrical appearance.
Tip: place your construction in place, align at both ends and secure them 7.6 cm long screws. Pre-drill the construction of the drill to avoid splitting the wood. Join structure on the top and use a 6.4 cm long screws.
Step 9
To do this job as a professional, install the interior of homes 0.65 cm thick plywood and fill 3.8 cm polyurethane foam between the beams of the structure. This is an important step that will enable the isolation of your dog crate. Make sure that there are no gaps between the polyurethane foam and the roof. If there are cracks, the cold air will enter and cool the interior of homes.
step 10
Use the same technique as written above to install insulation boards on the opposite side of the kennels, before final installation of the roof. You need to use 1.9 cm thick plywood and 5 cm long wood screw, to ensure that the plates are in the right place. Leave the front and rear overhang 3.8 cm, if you want to get the perfect look. Make sure that one side of the roof covering the other.
step 11
The next step of this enterprise is roofing tar paper and attach paper clips. Then set a nice roof covering starting from the lower left side of the roof. Useful advice is to create lines that will serve as the basis for setting up the roof structure, because the only way you will make a perfect parallel form, from top to bottom.
step 12
Last but not least, it is important to treat attention on the final details. Fill the holes putty, wood and trash it Waterproof filling gaps. Allow to dry for at least a composite few hours before polished with sandpaper surface. If you apply several coats of paint, you can protect the box from rotting. Twice Repaint exterior walls to get the desired appearance of the house and a neat appearance.
Once you go through this process you will become a true master of making homes for dogs, and if you manage to at least one dog off the street and give him a home fulfills the mission.
Нема коментара:
Постави коментар